Optimizing performance: A guide to radial shaft seals with a high coefficient of friction and compressive strength

Radialwellendichtring Typ A

Type A design

The sealing lip is aligned with the press-in direction.

Application: Normal, simple sealing points.

Assembly Instruction

Installation Step by Step

Dimension list

PK Design

Required Ordering Information

  • Radial shaft seal type A
  • Shaft diameter d1
  • Diameter of bore d2
  • Width of radial shaft seal b1
  • Material of collar
  • Material of supprot ring
  • Working temperature
  • Pressure (standard up to 10 bar)
  • Peripheral Speed (up to 32 m/s)
Radialwellendichtring Typ B

Type B design

The sealing lip faces in the opposite direction to the press-in direction.

Application: Normal, simple sealing points.

Assembly Instruction

Installation Step by Step

Dimesion list

PK Design

Required Ordering Information

  • Radial shaft seal type B
  • Shaft diameter d1
  • Diameter of bore d2
  • Width of radial shaft seal b1
  • Material of collar
  • Material of supprot ring
  • Working temperature
  • Pressure (standard up to 10 bar)
  • Peripheral Speed (up to 32 m/s)
Radialwellendichtring Typ AB

Design type AB

The sealing lips are aligned with the press-in direction.

Application: Sealing of compressed air and gases, sealing of difficult, low-lubrication sealing points.

Assembly Instruction

Installation Step by Step

Dimension list

PK Design

Required Ordering Information

  • Radial shaft seal type AB
  • Shaft diameter d1
  • Diameter of bore d2
  • Width of radial shaft seal b1
  • Material of collar
  • Material of supprot ring
  • Working temperature
  • Pressure (standard up to 10 bar)
  • Peripheral Speed (up to 32 m/s)
Radialwellendichtring Typ AC

Design type AC

The sealing lips are aligned in the same direction as the press-in direction and in the opposite direction.

Application: Correct separation of two media.

Assembly Instruction

Installation Step by Step

Dimension list

PK Design

Required Ordering Information

  • Radial shaft seal type AC
  • Shaft diameter d1
  • Diameter of bore d2
  • Width of radial shaft seal b1
  • Material of collar
  • Material of supprot ring
  • Working temperature
  • Pressure (standard up to 10 bar)
  • Peripheral Speed (up to 32 m/s)
Radialwellendichtring Typ BC

Design type BC

The sealing lips face in the opposite direction to the press-in direction.

Application: Sealing of compressed air and gases, sealing of difficult, low-lubrication sealing points.

Assembly Instruction

Installation Step by Step

Dimension list

PK Design

Required Ordering Information

  • Radial shaft seal type BC
  • Shaft diameter d1
  • Diameter of bore d2
  • Width of radial shaft seal b1
  • Material of collar
  • Material of supprot ring
  • Working temperature
  • Pressure (standard up to 10 bar)
  • Peripheral Speed (up to 32 m/s)
Radialwellendichtring Typ A-SF

Design type A-SF

Can be pressed in in both directions.

Application: Narrow design for tight installation conditions, for pressures up to 15 bar.

Assembly Instruction

Installation Step by Step

Dimension List

PK Design

Required Ordering Information

  • Radial shaft seal type A-SF
  • Shaft diameter d1
  • Diameter of bore d2
  • Width of radial shaft seal b1
  • Material of collar
  • Material of supprot ring
  • Working temperature
  • Pressure (standard up to 10 bar)
  • Peripheral Speed (up to 32 m/s)
Radialwellendichtring Typ B-SF

Design type B-SF

Can be pressed in in both directions.

Application: Narrow design for tight installation conditions, for pressures up to 15 bar.

Assembly Instruction

Installation Step by Step

Dimension List

PK Design

Required Ordering Information

  • Radial shaft seal type B-SF
  • Shaft diameter d1
  • Diameter of bore d2
  • Width of radial shaft seal b1
  • Material of collar
  • Material of supprot ring
  • Working temperature
  • Pressure (standard up to 10 bar)
  • Peripheral Speed (up to 32 m/s)
Radialwellendichtring Typ B-SF

Design type C-AC

The sealing lips are aligned in the same direction as the press-in direction and in the opposite direction.

Application: Correct separation of two media.

Assembly Instruction

Installation Step by Step

Dimension List

PK Design

Required Ordering Information

  • Radial shaft seal type C-AC
  • Shaft diameter d1
  • Diameter of bore d2
  • Width of radial shaft seal b1
  • Material of collar
  • Material of supprot ring
  • Working temperature
  • Pressure (standard up to 10 bar)
  • Peripheral Speed (up to 32 m/s)

Type C-AB

The sealing lips face in the opposite direction to the press-in direction.

Can be pressed in from both sides.

Application: Sealing of compressed air and gases, sealing of difficult, low-lubrication sealing points.

Assembly Instruction

Installation Step by Step

Dimension List

PK Design

Required Ordering Information

  • Radial shaft seal type C-AB
  • Shaft diameter d1
  • Diameter of bore d2
  • Width of radial shaft seal b1
  • Material of collar
  • Material of supprot ring
  • Working temperature
  • Pressure (standard up to 10 bar)
  • Peripheral Speed (up to 32 m/s)

Video Assembly Instruction